HUAWEI CDMA BTS 3606 PDF

Default Re: Huawei CDMA E BTS Max Power??? HI I think it can be more than 20W because the RF board support MAX 60W. The 3rd Global CDMA Operation and Development Forum, themed. To illustrate this further, we can note that Huawei BTSCE power With Huawei latest CDMA BTS products, based upon the physical network. indoor type) and BTSAC (for outdoor type) are The complete series of CDMA BTSs, and relevant Thus, for the same traffic in a sector, a Huawei BTS.

Author: Vomuro Yozshuhn
Country: Reunion
Language: English (Spanish)
Genre: Finance
Published (Last): 25 July 2009
Pages: 129
PDF File Size: 18.97 Mb
ePub File Size: 8.61 Mb
ISBN: 134-6-28687-465-4
Downloads: 78055
Price: Free* [*Free Regsitration Required]
Uploader: Akinokora

The cabinet is placed upside down. That is, 1 m 39 in. Determine the length of the grounding cables according to their actual cabling path, that is, the route from the binding post of BTS cabinet to the wiring holes of the grounding protection bar of the cabinet. For the proper storage, use and disposal of this product, national laws and regulations must be observed.

Huawei BTS3606 Installation Manual

Figure shows how to install a BTS cabinet on the cement floor. Otherwise, the equipment will suffer severe damages. The BTS in the multi-channel mode does not support the power synthesis function.

Don’t show me this message again. Page 15 The packing case is in good condition. Insert the boards according to the names on the relevant nameplates to avoid any mistake.

The packing case is in good condition. Mouse operation Action Description Press and hold the primary mouse button left mouse Select button by default. Figure Installing a cabinet on the floor without sufficient bearing capacity The last section also explains how to install cabinet assemblies on the cement cdms without sufficient bearing capacity.

  3213 SAYL MADEN KANUNU PDF

Installing Power Cables For the 24 V power input, the voltage drop of the cable from the 24 V power supply system to the power input port of the BTS must be less than or ddma to 0.

Huawei CDMA E BTS Max Power ???

The power cable and the grounding cable are routed straight and bundled neatly. Remove four bolts and one 36006 that connect the antistatic floor and the support.

Outline Figure shows the outline of A series support. Determine the installation location for the DDF according to the engineering design for the equipment room. The alarm box is correctly installed according to the design. Route the alarm cables coming in from the other side of the enclosure through the cabling holes on both sides of the 8-E1 module and then to the respective slots. Tighten the bolts on the cover. Connect one end of the cable to the working ground of the EAC.

Please feel free to contact our local office or company headquarters. GND cables for cdka cabling racks and for outdoor cabling racks. Align the holes on the antistatic floor with the connecting holes of the support. Cut the tapes along the seams of the carton cover using a knife.

CDMA grows greener – Huawei Publications

If the power supply is on during the operation, do not touch the binding posts with the adjustable wrench or the screwdriver. Comments to this Manuals Your Name. Wooden cases are generally used to pack heavy objects like racks, batteries, and so on.

  GLORIA SANZ PINYOL COMUNICACION EFECTIVA EN EL AULA PDF

The sectional area is 35 cables VL: Installing Other Functional Modules Normally, the fan box is installed upon delivery. Chapter 1 Installation Preparations introduces how to arrange the personnel arrangement, check the installation environment check, huawej project plan and make kickoff coordination, and conduct the unpacking check.

Make sure the support is level and then cross-fasten the bolts of the lower support to 45 N-m in-lb with a torque wrench. Watch out for the sharp edges on the RF fan panel during the installation of RF cables lest it hurt your fingers.

When handling the cabinet, hold on the solid places such as the upper cable rack or bone frame. Page of 93 Go.

CDMA grows greener

Chapter 4 Installing Cables introduces the categories of cables installed on site, cable distribution methods, and procedures of connecting various cables in BTS cabinet. Leveling the lower support See section 2. Clamp the cables to the bracket.

Lead the cables into their corresponding cable-fixing troughs. For the specific method, see section 2. If the outer package is damaged or soaked; or the equipment is soaked and becomes rusty, stop unpacking and find the cause.