Préampli-Processeur CHORD DSP R VENDU TRÈS RARE! Préampli processeur exceptionnel en HC et, fait beaucoup plus rare. Chord dsp r preamp / surround controller, boxed. CHORD DSP R preamp/ surround controller. with dts and dolby 2 surround. Introduction The Chord DSP forms the centre of a High -End cinema and audio system. The DSP decodes Dolby Digital, DTS and DTS-ES and has the.

Author: Mazurr Satilar
Country: Japan
Language: English (Spanish)
Genre: Environment
Published (Last): 8 March 2011
Pages: 365
PDF File Size: 11.16 Mb
ePub File Size: 13.33 Mb
ISBN: 440-2-98922-277-8
Downloads: 73047
Price: Free* [*Free Regsitration Required]
Uploader: Vudojind

To access the connector side, lift the hinged flap on the right-hand side of vhord DSP Chord products are designed to be connected using balanced leads. This setting overrides the Treble setting in the Tone Setup. The preset set -up defines the parameters of each preset and allows control over the following levels: This processing mode offers a sound with a large to emulate that of a live concert.

DSP 8000 AV Processor

The diagram of the mechanical buttons is shown below. The speaker levels should normally be set at 75dB. This has the effect of replacing the unbalanced audio input for that particular source. This mechanical button is used to return to the main menu of the remote control where the menus of other Chord products may be accessed. If the knob is pressed whilst in the user interface menus then you will enter the selected sub menu. Unbalanced inputs use RCA phono connectors that are gold plated with teflon high performance dielectric in sulators for optimum performance.

This means that the DSP will automatically check for incoming digital audio signals, composite video signals and S- Video signals. When the buttons are locked they will not work if you press them.

This button functions as a toggle to mute and un -mute the outputs. Trigger 2 duration See Trigger 1 duration. This takes a few minutes to complete. Play in some music from your input source and see if the signal clips on the meter on the screen. If this is set to Infin.


Pin 1 is earth, pin 2 is positive and pin 3 is negative. CopyrightDigital Theatre Systems, Inc. Up to seven characters are allowed for each source name. Tone setup Treble and bass adjustment, plus settings for the treble and bass corner frequencies. The distance each of your speakers are from the listening position are entered so that the DSP can automatically adjust delays of signals to speakers to compensate for different configurations.

This menu allows you to adjust the level of each of individual loudspeaker output.

DSP AV Processor |

Three component video inputs and one output support HDTV-formats. Use the left and right cursor LCD touch pads or front panel buttons to adjust the gain setting so that the signal never clips.

Dsp8000g time the button is pressed the selected input source will be incremented by one. If this is the case please ensure that: See the table for Trigger 1 as it is the same is the same for Trigger 2. TAPE This button is used to monitor the level and quality of your audio recording signal.

It is particularly effective for recordings which have strong left – or right-channel elements in the mix, as these are detected and accentuated by the Panorama process. Press this button to move downwards through the sub menus within the set up menus.

Subwoofer This setting allows you to control the level of the subwoofer speaker for the selected preset. VOLUME To decrease the dsp800r or decrease parameter settings in the user interface menus, turn the volume knob anticlockwise. The information that is shown includes the selected input source, the signal type, any music mode that is selected, the video format and the current volume settings.

Turn the microphone ON. We hope you have many hours of enjoyment from this product. Ease of use and set up is one major feature of the DSP Place the microphone on the listening position pointing towards the roof.


MODE This button is used to cycle through the available post processing modes. The DSP is not designed to switch between video domains.

吏„?•?œ ?„濡œ GLV – Create arts through technology!

With the three 12VDC triggers and the RS interface the use of the DSP in a home automation system adds to its already long list of features and advantages over the compet ition. The touch pads that allow you to navigate to the other pages are also highlighted.

These are shown in the diagram below. If the selected source does have a component video connection then you must assign this setting the a value from 1 to 3 depending on sdp8000r set of component video inputs you are using. Make sure that you connect the correct colour connectors to each other.

You can use this function to avoid sudden peaks in the sound volume without losing any of the detail. This can be done via the front panel Page 27 – 29 or the Chord Touch srceen remote Page Enhanced bass If you wish to add chor bass to your system, you can use the Enhanced bass function. Dsp8000r should then adjust each loudspeaker level setting so that the SPL meter reads the same measurement for each loudspeaker tone.


Analogue audio connections can be split into two groups; unbalanced and balanced. Each press of this LCD touch pad will cycle through each loudspeaker setting. This processing mode offers a natural sound with no reverb added.